Model 599

Check-in Conveyor


Check-In conveyors are the first point of interface between the passenger and the baggage handling system, they allow passengers to safely enter their baggage onto the conveying system. They also allow the check-in desk clerk to weigh and label the baggage.



Model 599 Check-In Conveyors

The Model 599 Check-in Conveyor range has been designed to meet the specific needs of airports. Our weigh, label and despatch conveyors can be configured as either one, two or three stage check-in systems, offering choice and flexibility for check-in operations. The Model 599 Check-in Conveyors are finished in stainless steel to a very high quality. As standard they are fitted with dummy end pulleys to eliminate trap points for passengers, operators, bag straps and labels. For extra security safety gates may be fitted to the weigh conveyor preventing passengers from entering the check-in areas when the desks are closed.


Application Benefits

Motorised Drive

Compact conveyor design with proven reliability

Short Faced End Pulley

Eliminates trap points by the use of dummy pulleys

Conveyors Mounted on Guide Wheels

Complete unit can be easily withdrawn for maintenance and cleaning

Plug and Play

Interchangeable conveyors enables remote maintenance

Drop Down Front Cladding Panel

Facilitates the removal of weigh conveyor without special tooling

Fire Retardant Belting to ISO 340

Reduces the spread of fire

Modular Design

Facilitates installation and any subsequent modifications

Design Flexibility

Accommodate variations such as sidewall height, bed width, drive components etc.

Reinforced bed plates

Increases load capacity of conveyor

State of the Art PLC Controls

Use of standard PLC technology enables clients’ handling / screening schemes to be complemented

Design Options

Standard Variations

Check-In Type

One stage, two stage or three stage

Belt Width

400mm, 450mm, 500mm, 550mm or 600mm

Sidewall Height

50mm, 300mm or 450mm

Safety Gate

Fitted or Not Fitted

Turning Drums

Parallel or tapered turning drums can be fitted at junction with collector

Belt Speeds

Normally – Weigh 0.5m/s Label 0.8m/s Despatch 1.0m/s Others available if required

General Description

Model 599 Check-In Conveyor - Stage Options

One Stage: Bags are weighed, labelled and despatched on a single conveyor.
Two Stage: Usually the weighing and label operations are carried out on a single conveyor. Baggage is
injected onto the Collector Conveyor from the Despatch Conveyor.
Three Stage: Separate conveyors are used for the weigh, label and despatch functions.

General Construction – Weigh, Label and Despatch Conveyors

Drive/Head Pulley

135mm diameter 0.75kw motorised drum mounted within moulded end caps. The face width of the drum is narrower than the belt, and the end caps are formed such that they act as a dummy pulley (or static shroud).

Tail Pulley

75mm diameter end pulleys are machined and fitted to 20mm diameter bright mild steel axles mounted in sealed for life precision bearings. The face width of the pulley is narrower than the belt, and plastic bushes are located at the end of the shaft to act as dummy pulleys.

Drive & Tail Snubber Pulley

The Drive Snubber Pulley is 75mm diameter, the tail pulley is 50mm diameter. The drive snubber pulley ensures that the pulley wrap on the drive drum is kept to a maximum. Both are screw adjustable for belt tracking and tensioning purposes.


Sidewalls are formed from 2.0mm thick Stainless Steel. The sidewalls are bolted to both sides of the bed section, additionally there are formed mild steel cross members which connect the two sides together underneath the bed section. This ensures good rigidity. The sidewalls can be quickly removed for maintenance or cleaning purposes.

Bed Section

Press-formed channel section from 2.5mm thick mild steel, width equal to belt width plus 20mm and 50mm deep. Stainless cladding. The front panel is manufactured from 2.5 mm thick stainless steel. The Daifuku Logan logo is fixed on to this panel. The panel can be unlatched and pivoted down to allow access under the conveyor for cleaning, and to facilitate conveyor removal. The outer sides of all conveyors in full public view will be clad with 1.6 mm polished stainless steel panels.

Tracks and Castors

All of the Check-In conveyors are mounted on castors which run in a track, the weigh conveyor tracks are fixed to the top of the weigh scale. The conveyors are retained in their operating position by a latch bolt. Access to the weigh conveyor bolt is via the hinged stainless steel plate. This allows for easy removal of the units for cleaning and maintenance purposes.


Two ply polyester endless with PVC cover and diamond pattern top.

Latest News
Latest News
by Administrator 23-03-2015
WORLDS 2ND LARGEST MATERIAL HANDLING COMPANY By Josh Bond, Associate Editor Let’s start our annual look at the Top 20 systems suppliers...
Latest News
Latest News
by Administrator 01-07-2014
Daifuku to Acquire New Zealand-based BCS Group Limited Daifuku Co., Ltd. (“Daifuku”) announced today it has entered into an agreement...


Hull All Over The World



© Daifuku Logan  Ltd - VAT number is GB 433 5332 73 - Registered in England - Company Number 3116545
Daifuku Logan Ltd Fair Processing Notice | Anti-slavery statement 2019
Standard Conditions of Purchase May 2018 | 066I - Supply Conditions Construction Scheme Mar 2018 | DLL- 066 Supply Conditions - Mar 2018